This article mainly introduces:

Saudi Arabia hydraulic cylinder,spring return cylinder manufacturer,spring return cylinder

(Saudi Arabia spring return cylinder,produced by Hengyu Group）

spring return cylinder are widely used in Saudi Arabia，because of high work efficiency，long service life，smooth movement.So our company has designed spring return cylinder for customers from Saudi Arabia.

Introduction to spring return cylinder:

If the spring return cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the spring return cylinder. The internal parts of the spring return cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the spring return cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the spring return cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the spring return cylinder bore processing is out of whack. Because the piston and spring return cylinder, guide rail and piston rod are relative If the spring return cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling spring return cylinder weight composition and calculation. The weight of the spring return cylinder is composed of the spring return cylinder diameter, the outer diameter and weight of the spring return cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

When the spring return cylinder is disassembled due to oil leakage and other faults, the position of the piston should be moved to any end position of the spring return cylinder by applying liquid pressure. Improper tapping and sudden drop should be avoided during disassembly.

Classification of spring return cylinder: according to the mode of movement it can be divided into linear reciprocating movement type and rotary swing type; According to the effect of liquid pressure, it can be divided into single acting type and double acting type. According to the structure, it can be divided into piston type, plunger type, multistage telescopic sleeve type, pinion and rack type, etc. According to the installation form can be divided into rod, earring, foot, hinge shaft and so on; According to the pressure grade can be divided into 16Mpa, 25Mpa, 31.5Mpa and so on.

spring return cylinder daily maintenance, should focus on checking whether the piston rod surface roughness and shape and position tolerance meet the technical requirements, if the piston rod bending should be calibrated to meet the requirements or according to the physical mapping, manufactured by a professional manufacturer. If the piston rod surface coating wear, slip damage, local spalling can be adopted to remove the coating, re-chrome surface processing process.

Answers to some questions about spring return cylinder:

How to limit cylinder push rod rotation?
In general, the push-rod rotation can be limited after the push-rod is connected to the pushed mechanism. For example, the push rod is hinged with the push mechanism, or the push mechanism itself is guided, which can limit the rotation of the push rod.

To achieve the same stroke, which is better, hydraulic cylinder or lead screw?
If there is batch action, then the hydraulic pressure is better. Hydraulic: smooth operation, no lubrication, easy control, high control accuracy (can use proportional or servo system), the key is to manually control, but certainly to support the hydraulic system, for a single action must cost. Maintenance costs are also high. Lead screw: simple structure, easy to achieve, convenient maintenance, but must be lubricated, can not be manual, or manual control is inconvenient. See where it is used, if it is used in high-precision occasions, it must only be hydraulic, because the lead screw has a gap. There are many hydraulic actions, the hydraulic system itself must be prepared, then the use of hydraulic pressure is also very economical.