This article mainly introduces:

Oman hydraulic cylinder,reciprocating cylinder manufacturer,reciprocating cylinder

(Oman reciprocating cylinder,produced by Hebei Hengyu company）

reciprocating cylinder are widely used in Oman，because of simple structure and reliable operation，excellent temperature resistance，no transmission clearance.So our company has designed reciprocating cylinder for customers from Oman.

Introduction to reciprocating cylinder:

reciprocating cylinder daily maintenance, should focus on checking whether the piston rod surface roughness and shape and position tolerance meet the technical requirements, if the piston rod bending should be calibrated to meet the requirements or according to the physical mapping, manufactured by a professional manufacturer. If the piston rod surface coating wear, slip damage, local spalling can be adopted to remove the coating, re-chrome surface processing process.

The body of the reciprocating cylinder on the processing process requirements: the body of the reciprocating cylinder is an important and essential part of the reciprocating cylinder, because it has an irreplaceable role. The processing requirements for this part are very high, requiring that the surface roughness of the reciprocating cylinder after processing should reach 0.4-0.8um, and the coaxiality and wear resistance requirements are also very high.

The reciprocating cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and does linear reciprocating motion (or swinging motion). It is simple in structure and reliable in operation. When it is used to achieve reciprocating movement, the deceleration device can be eliminated, and there is no transmission gap, and the movement is smooth, so it is widely used in various mechanical hydraulic systems. The output force of the reciprocating cylinder is proportional to the effective area of the piston and the pressure difference between the two sides; The reciprocating cylinder is basically composed of reciprocating cylinder and reciprocating cylinder head, piston and piston rod, sealing device, buffer device and exhaust device. Buffer device and exhaust device depending on the specific application, other devices are essential.

In order to ensure the service life of the reciprocating cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

Answers to some questions about reciprocating cylinder:

How is the hydraulic cylinder tempered?
The purpose of the tempering treatment is to make the piston rod have comprehensive mechanical properties of strength, hardness, plasticity and toughness, and the internal structure is uniform and fine tempered sorbite, so as to prepare the organization for subsequent surface quenching. The length of the long cylinder piston rod is 3800-4200, and the diameter is Φ90-Φ110mm, so its heating equipment uses a 150KW well resistance furnace or 600KW suspension continuous resistance heating furnace, and the temperature is controlled by two areas. Heat treatment process parameters: in the shaft furnace, a furnace is suspended with 4 pieces, the quenching heating temperature is 830±10℃, and after holding heat for 160min, it is divided into two times for quenching, and two pieces are quenched each time, and the circulating cooling water is used for cooling.

Classification and application of cylinders.
Hydraulic cylinder is divided into single acting hydraulic cylinder, double acting cylinder, combined hydraulic cylinder, swing hydraulic cylinder. Single acting cylinder is divided into plunger type hydraulic cylinder, single piston rod hydraulic cylinder, double piston rod hydraulic cylinder, telescopic hydraulic cylinder. Plunger type hydraulic cylinder: the plunger moves only in one direction, and the return stroke is to push the plunger back using its own weight or load. Single piston rod hydraulic cylinder: The piston moves only in one direction, and the return stroke is to push the plunger back using dead weight or load. Double piston rod hydraulic cylinder: both sides of the piston are equipped with piston rods, and pressure oil can only be supplied to one side of the piston. The return stroke usually uses spring force, gravity or external force. Telescopic hydraulic cylinder: It obtains long stroke with short cylinder. The hydraulic oil is pushed out from large to small section by section, and the external force is reduced from small to large.